وصلت سالمة. الإنطباعات الأولى كانت لوك دافئاً كما تبدو اللوحة رثّة، لكنّها كانت مجرّد تدفق غير مُغْسَل. هناك سهم مفيد يساعدك في توصيل ESSP01s بالطريقة الصحيحة، وتوخ الحذر من السهل الحصول على خطأ. لاستخدامه كمبرمج لـ Ardino IDE، كل ما عليك فعله هو إضافة مفتاح بسيط بين IO0 وGND لإدخاله إلى وضع الفلاش. بسيط.

Arrived safe and sound. First impressions were luke warm as the board look tatty, but it was just unwashed flux. There is a handy arrow ti assist you in getting the ESP01s plugged in the right way around, and be careful it is very easy to get wrong. To use it as a programer for the Arduino IDE, all you need to do is add a simple switch between IO0 and GND to get it in to flash mode. Simple.

وصلت سالمة. الإنطباعات الأولى كانت لوك دافئاً كما تبدو اللوحة رثّة، لكنّها كانت مجرّد تدفق غير مُغْسَل. هناك سهم مفيد يساعدك في توصيل ESSP01s بالطريقة الصحيحة، وتوخ الحذر من السهل الحصول على خطأ. لاستخدامه كمبرمج لـ Ardino IDE، كل ما عليك فعله هو إضافة مفتاح بسيط بين IO0 وGND لإدخاله إلى وضع الفلاش. بسيط.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

....

....

....

While plug using 3 different item ESP8266 the unit overheat need to remove quick

While plug using 3 different item ESP8266 the unit overheat need to remove quick

While plug using 3 different item ESP8266 the unit overheat need to remove quick

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

For this Programmer the ESP-Module has to be placed outwards. For me the standard DTR/CTS control for programming is not working using Arduino IDE! First of all I had to solder a pullup resistor between VCC and the CD_PD pin. To put the ESP-01 in programming mode GPIO has to be pulled to ground (soldered a jumper to the pin) followed by pressing the Reset button. For Nral opreation the Jumper should be removed again.

Ottimo prodotto funziona correttamente

Ottimo prodotto funziona correttamente

Ottimo prodotto funziona correttamente

وصلت في ظروف جيدة

arrived in good conditions

وصلت في ظروف جيدة

يقوم بالعمل

Fait le job

يقوم بالعمل

مفيد لـ esp01s

Utile per esp01s

مفيد لـ esp01s

عناصر جيدة

GOOD ITEMS

عناصر جيدة